Bathroom Extract Fans
In-line Duct Fans
Wall or Window Extract Fans
Heat Recovery Units
Whole house Extract Units
Acoustic Cabinet Fans
Roof mounted fans
Kitchen Extract Fans 
Kitchen Extract Hoods 
Comfort Cooling Range
Hand and Hair Dryers 
Air Handling Units
Plate Mounted Axial Flow 
Cylindrical Cased Axial Flow Fans 
Centrifugal Direct Drive Fan 
Parking Ventilation 
Smoke Extract Fans 
Atex Fans for Explosive Hazardous 
Heating Industrial Range 
Backward curved centrifugal fans
High pressure centrifugal fans with backward curved impeller
High pressure centrifugal fans with forward curved impeller
Centrifugal fans with forward curved impeller
Double inlet centrifugal fans
Radial Centrifugal fans for transportation of materials
Centrifugal fans for furnace applications
Mounting Accesories 
Electrical Accessories
Direct drive, single inlet centrifugal fan. Manufactured from steel sheet protected with cataforesis primer + polyurethane paint finish RAL 7045.
Designed to continuously circulate air from -20ºC up to 100ºC.
Standard arrangement
• Arrangement 4: Direct drive. Impeller directly mounted on motor shaft. B3 motor is supported by the pedestal. Max air temperature 100°C. With cooling disk up to 220°C.
• Arrangement 5: Direct drive. Impeller directly mounted on motor shaft. B5 motor is fitted on casing sideplate.
• Arrangement 8: Flexible coupling. Overhung impeller. Support and motor mounted on a base outside the air stream. Max air temperature 100°C. With cooling disk up to 300°C.
Motors
2 or 4 pole, IE 3* high efficiency, three-phase 230/400V 50Hz up to motor size 112 and 400/690V 50Hz for higher motors. IP55 protection, class F.
* From 0,75kW, motor can be IE 2 and controlled by VSD.
On request
• Manufactured from different materials.
• 60 Hz versions.
• Painted in different RAL colour.
• Hot dip galvanized static parts.
• Corrosion proof construction.
• Wear proof construction.
• Motors for special applications.
• Motors suitable for VSD.
• Accessories: Flexible joints, inspection door, casing drain, AV-mounts, protection nets, filter, silencer, inlet discharge governor, valves, dampers.
• Gas tight construction.
• Thermal insulation.
Designed to continuously circulate air from -20ºC up to 100ºC.
Standard arrangement
• Arrangement 4: Direct drive. Impeller directly mounted on motor shaft. B3 motor is supported by the pedestal. Max air temperature 100°C. With cooling disk up to 220°C.
• Arrangement 5: Direct drive. Impeller directly mounted on motor shaft. B5 motor is fitted on casing sideplate.
• Arrangement 8: Flexible coupling. Overhung impeller. Support and motor mounted on a base outside the air stream. Max air temperature 100°C. With cooling disk up to 300°C.
Motors
2 or 4 pole, IE 3* high efficiency, three-phase 230/400V 50Hz up to motor size 112 and 400/690V 50Hz for higher motors. IP55 protection, class F.
* From 0,75kW, motor can be IE 2 and controlled by VSD.
On request
• Manufactured from different materials.
• 60 Hz versions.
• Painted in different RAL colour.
• Hot dip galvanized static parts.
• Corrosion proof construction.
• Wear proof construction.
• Motors for special applications.
• Motors suitable for VSD.
• Accessories: Flexible joints, inspection door, casing drain, AV-mounts, protection nets, filter, silencer, inlet discharge governor, valves, dampers.
• Gas tight construction.
• Thermal insulation.
ATEX versions
On request, explosion proof versions in accordance with ATEX directive for three phase models:
Ambient temperature -20°C to +60°C, ambient pressure (abs.) 0,8 bar to 1,1 bar according to EN 14986.
• Gas:
2G IIB T2-T3-T4, Motor Exd IIB or ExeII
2G IIB+H2 T2-T3-T4, Motor ExdIIc
3G IIB T2-T3-T4, Motor ExnA (only for 3G zone)
3G IIB+H2 T2-T3-T4, Motor ExnA (only for 3G zone)
• Non-conductive dust
2D IIIB T125°C-T135°C-T195°C-T295°C
3D IIIB T125°C-T135°C-T195°C-T295°C
• Conductive dust (compulsory IP 65 motor):
2D IIIC T125°C-T135°C-T195°C-T295°C
3D IIIC T125°C-T135°C-T195°C-T295°C
On request, explosion proof versions in accordance with ATEX directive for three phase models:
Ambient temperature -20°C to +60°C, ambient pressure (abs.) 0,8 bar to 1,1 bar according to EN 14986.
• Gas:
2G IIB T2-T3-T4, Motor Exd IIB or ExeII2G IIB+H2 T2-T3-T4, Motor ExdIIc3G IIB T2-T3-T4, Motor ExnA (only for 3G zone)3G IIB+H2 T2-T3-T4, Motor ExnA (only for 3G zone)• Non-conductive dust
2D IIIB T125°C-T135°C-T195°C-T295°C3D IIIB T125°C-T135°C-T195°C-T295°C• Conductive dust (compulsory IP 65 motor):
2D IIIC T125°C-T135°C-T195°C-T295°C3D IIIC T125°C-T135°C-T195°C-T295°C -
Backward curved impeller
